Category:AVRDUDE
Use
You should get that response, which means that it communicated with the programmer but failed to find a connected chip.
If the programmer is not found, you will get this response:
If you connect the programmer to a target (say an attiny2313 target board) and run avrdude -c usbtiny -p t2313 you should get the following which indicates it communicated properly with the chip.
Avrdude GUI
- Avrdudess
- GUI version - AVR8 Burn-O-Mat: a GUI for avrdude
- Avrdude-GUI designed by yuki-lab - Read the fuse, select programmer and IC, upload the hex file. You can also get the 1.05 version directly from this link.
Commands and Options
| Description | CMD |
|---|---|
| Use terminal mode |
|
| Fusebit setup | avrdude -P comport -b 19200 -c avrisp -p m328p -v -e -U efuse:w:0x05:m -U hfuse:w:0xD6:m -U lfuse:w:0xFF:m |
| Upload flash | avrdude -P comport -b 19200 -c avrisp -p m328p -v -e -U flash:w:hexfilename.hex -U lock:w:0x0F:m |
- -c choose programmer
Programmer Arduino as ISP -> avrisp usbasp -> usbasp
- -C config file -> ..\etc\avrdude.conf
- -p mode
- -t terminal mode
- -P choose port
- -U flash:w:"E:\xxx\Desktop\aaa.hex":a, write flash
- -U flash:r:"E:\he\Desktop\aaa.hex":a, read flash
- -U eeprom:w:"E:\he\Desktop\aaa.eep":a, auto
- -P comport, -b baudrate, -B bitlock
- L low fuse, H high fuse, E extended fuse, Lock bits
- -F force, -V disable verify, -D disable flash erase, -e erase flash and eeprom, -n do not write,
- -vvvv verbose
Tutorial
Documents
Boards file of arduino bootloader
- uno.vid.0=0x2341
- uno.pid.0=0x0043
- uno.vid.1=0x2341
- uno.pid.1=0x0001
- uno.vid.2=0x2A03
- uno.pid.2=0x0043
- uno.vid.3=0x2341
- uno.pid.3=0x0243
- uno.upload.tool=avrdude
- uno.upload.protocol=arduino
- uno.upload.maximum_size=32256
- uno.upload.maximum_data_size=2048
- uno.upload.speed=115200
- uno.bootloader.tool=avrdude
- uno.bootloader.low_fuses=0xFF
- uno.bootloader.high_fuses=0xDE
- uno.bootloader.extended_fuses=0x05
- uno.bootloader.unlock_bits=0x3F
- uno.bootloader.lock_bits=0x0F
- uno.bootloader.file=optiboot/optiboot_atmega328.hex
- uno.build.mcu=atmega328p
- uno.build.f_cpu=16000000L
- uno.build.board=AVR_UNO
- uno.build.core=arduino
- uno.build.variant=standard
Driver
| Drive | Purpose | - |
|---|---|---|
| libusbK | avrdude | - |
| lisusb-win32 | digi spark, EDAtiny | - |
Fuse Bit
| Type Board | Low | High | Extend | Lock | |
|---|---|---|---|---|---|
| EDAtiny | 0xE1 | 0xDD | 0xFE | - | |
| UNO | FF | DE | 05 | 0F |
- new wiki page link: https://w2.electrodragon.com/SDK/avrdude-dat/avrdude-dat.md
This category currently contains no pages or media.