Category:AVRDUDE

Use

• 

  You should get that response, which means that it communicated with the programmer but failed to find a connected chip.

• 

  If the programmer is not found, you will get this response:

• 

  If you connect the programmer to a target (say an attiny2313 target board) and run avrdude -c usbtiny -p t2313 you should get the following which indicates it communicated properly with the chip.

Avrdude GUI

• Avrdudess
• GUI version - AVR8 Burn-O-Mat: a GUI for avrdude
• Avrdude-GUI designed by yuki-lab - Read the fuse, select programmer and IC, upload the hex file. You can also get the 1.05 version directly from this link.

Commands and Options

Description	CMD
Use terminal mode	avrdude -p m8 -c usbasp -C ..\etc\avrdude.conf -t dump eeprom 0 512
Fusebit setup	avrdude -P comport -b 19200 -c avrisp -p m328p -v -e -U efuse:w:0x05:m -U hfuse:w:0xD6:m -U lfuse:w:0xFF:m
Upload flash	avrdude -P comport -b 19200 -c avrisp -p m328p -v -e -U flash:w:hexfilename.hex -U lock:w:0x0F:m

• -c choose programmer

Programmer Arduino as ISP -> avrisp
usbasp -> usbasp

• -C config file -> ..\etc\avrdude.conf
• -p mode
• -t terminal mode
• -P choose port
• -U flash:w:"E:\xxx\Desktop\aaa.hex":a, write flash
• -U flash:r:"E:\he\Desktop\aaa.hex":a, read flash
• -U eeprom:w:"E:\he\Desktop\aaa.eep":a, auto
• -P comport, -b baudrate, -B bitlock
• L low fuse, H high fuse, E extended fuse, Lock bits
• -F force, -V disable verify, -D disable flash erase, -e erase flash and eeprom, -n do not write,
• -vvvv verbose

Tutorial

• 

Documents

• File:Avrdude-6.3.0-arduino8-i686-w64-mingw32.zip

Boards file of arduino bootloader

• uno.vid.0=0x2341
• uno.pid.0=0x0043
• uno.vid.1=0x2341
• uno.pid.1=0x0001
• uno.vid.2=0x2A03
• uno.pid.2=0x0043
• uno.vid.3=0x2341
• uno.pid.3=0x0243
• uno.upload.tool=avrdude
• uno.upload.protocol=arduino
• uno.upload.maximum_size=32256
• uno.upload.maximum_data_size=2048
• uno.upload.speed=115200
• uno.bootloader.tool=avrdude
• uno.bootloader.low_fuses=0xFF
• uno.bootloader.high_fuses=0xDE
• uno.bootloader.extended_fuses=0x05
• uno.bootloader.unlock_bits=0x3F
• uno.bootloader.lock_bits=0x0F
• uno.bootloader.file=optiboot/optiboot_atmega328.hex
• uno.build.mcu=atmega328p
• uno.build.f_cpu=16000000L
• uno.build.board=AVR_UNO
• uno.build.core=arduino
• uno.build.variant=standard

Driver

• Use this tool to change driver for OS like win-10

Drive	Purpose	-
libusbK	avrdude	-
lisusb-win32	digi spark, EDAtiny	-

Fuse Bit

Type Board	Low	High		Extend	Lock
EDAtiny	0xE1	0xDD	0xFE	-
UNO	FF	DE	05	0F

- new wiki page link: https://w2.electrodragon.com/SDK/avrdude-dat/avrdude-dat.md