ESP Relay Board VDC - Revision history

Chao at 07:18, 22 April 2024

2024-04-22T07:18:35Z

← Older revision		Revision as of 15:18, 22 April 2024
Line 1:		Line 1:
	# redirect page - https://w2.electrodragon.com/gollum/search?q=NWI1115-dat.md		redirect page - https://w2.electrodragon.com/gollum/search?q=NWI1115-dat.md

Chao at 07:18, 22 April 2024

2024-04-22T07:18:26Z

← Older revision		Revision as of 15:18, 22 April 2024
Line 1:		Line 1:
	~~==== Update Log for ESP Relay Board VDC ====~~		# redirect page - https://w2.electrodragon.com/gollum/search?q=NWI1115-dat.md
	~~<gallery>~~
	~~File~~:~~ESP_Relay_Board_Configuration_V4~~.2.~~png \| Latest version of ESP Relay Board VDC version V4.2~~
	~~File:ESP_DC_Relay_Board_01.JPG \| (Old version)~~
	~~File:Wifi_iot_relay_board_VDC.png \| Schematic~~
	~~File:ESP_Relay_Board_VDC_silk_print.png \| VDC Relay board latest silk print 4.2~~
	</~~gallery>~~
	* V4.2 added voltage divider on back side of PCB, this need to be soldered manually.
	* V4.1 pin headers changed to two group. RST, ADC and DHT_IO16 pins on left side now.

Chao: /* Analag Input A0 */

2024-04-22T07:14:47Z

Analag Input A0

← Older revision		Revision as of 15:14, 22 April 2024
Line 8:		Line 8:
	* V4.2 added voltage divider on back side of PCB, this need to be soldered manually.		* V4.2 added voltage divider on back side of PCB, this need to be soldered manually.
	* V4.1 pin headers changed to two group. RST, ADC and DHT_IO16 pins on left side now.		* V4.1 pin headers changed to two group. RST, ADC and DHT_IO16 pins on left side now.
	~~== Analag Input A0 ==~~
	~~{\| class="wikitable"~~
	\|-
	~~! Back Side Jumper !! Header text~~
	\|-
	~~\| Connect \|\| No voltage divider, A0 directly connect to ESP-12 Module ADC pin.~~
	\|-
	~~\| Disconnect \|\| A0 input via voltage divider to ADC = 220K / 100K, maximium input A0 3.3V~~
	\|}
	* Reference calculation see here: https://learn.sparkfun.com/tutorials/voltage-dividers/all

Chao: /* Specific for Relay Board VDC */

2024-04-22T07:14:37Z

Specific for Relay Board VDC

← Older revision		Revision as of 15:14, 22 April 2024
Line 18:		Line 18:
	\|}		\|}
	* Reference calculation see here: https://learn.sparkfun.com/tutorials/voltage-dividers/all		* Reference calculation see here: https://learn.sparkfun.com/tutorials/voltage-dividers/all

	~~== Specific for Relay Board VDC ==~~
	~~{\| class="wikitable sortable"~~
	\|-
	~~! Jumper !! Header text !! Header text~~
	\|-
	~~\| U2 \|\| wireless RF receiver, output TTL signal to ESP12F pins, DO -> IO2, D1 -> IO15\|\| -~~
	\|-
	~~\| JP2 \|\| Alternative power supply pin 5V-24V, = terminal power input \|\| -~~
	\|-
	~~\| JP7 \|\| Power input selection, choose between 5V or 5-24V.\|\| -~~
	\|-
	~~\| JP1 \|\| DHT, ADC, RST \|\| -~~
	\|-
	~~\| JP6 \|\| row 1: RXD, TXD, 5V, GND, row 2: 3.3V, IO4, IO5, IO15 \|\| -~~
	\|-
	~~\| Green Out Input Terminal \|\| VIN 5-26V (top / inside of the board), ground (close to the edge outside of the board) \|\| -~~
	\|}

Chao: /* Use of AC Main Power IN to Relay */

2024-04-22T07:13:30Z

Use of AC Main Power IN to Relay

← Older revision		Revision as of 15:13, 22 April 2024
Line 36:		Line 36:
	\| Green Out Input Terminal \|\| VIN 5-26V (top / inside of the board), ground (close to the edge outside of the board) \|\| -		\| Green Out Input Terminal \|\| VIN 5-26V (top / inside of the board), ground (close to the edge outside of the board) \|\| -
	\|}		\|}

	~~== Use of AC Main Power IN to Relay ==~~
	* to switch to control AC mains power, need to remove two 1206 0R resistors on board. Then power from left green terminal = relay output (and terminal)
	* To supply power on board control circuit, add 6-24V power to "ALT VIN" pins
	~~[[category: ESP Relay Board]]~~

Chao at 04:19, 9 July 2020

2020-07-09T04:19:14Z

New page

==== Update Log for ESP Relay Board VDC ====
<gallery>
File:ESP_Relay_Board_Configuration_V4.2.png | Latest version of ESP Relay Board VDC version V4.2
File:ESP_DC_Relay_Board_01.JPG | (Old version)
File:Wifi_iot_relay_board_VDC.png | Schematic
File:ESP_Relay_Board_VDC_silk_print.png | VDC Relay board latest silk print 4.2
</gallery>
* V4.2 added voltage divider on back side of PCB, this need to be soldered manually.
* V4.1 pin headers changed to two group. RST, ADC and DHT_IO16 pins on left side now.
== Analag Input A0 ==
{| class="wikitable"
|-
! Back Side Jumper !! Header text
|-
| Connect || No voltage divider, A0 directly connect to ESP-12 Module ADC pin.
|-
| Disconnect || A0 input via voltage divider to ADC = 220K / 100K, maximium input A0 3.3V
|}
* Reference calculation see here: https://learn.sparkfun.com/tutorials/voltage-dividers/all

== Specific for Relay Board VDC ==
{| class="wikitable sortable"
|-
! Jumper !! Header text !! Header text
|-
| U2 || wireless RF receiver, output TTL signal to ESP12F pins, DO -> IO2, D1 -> IO15|| -
|-
| JP2 || Alternative power supply pin 5V-24V, = terminal power input || -
|-
| JP7 || Power input selection, choose between 5V or 5-24V.|| -
|-
| JP1 || DHT, ADC, RST || -
|-
| JP6 || row 1: RXD, TXD, 5V, GND, row 2: 3.3V, IO4, IO5, IO15 || -
|-
| Green Out Input Terminal || VIN 5-26V (top / inside of the board), ground (close to the edge outside of the board) || -
|}

== Use of AC Main Power IN to Relay ==
* to switch to control AC mains power, need to remove two 1206 0R resistors on board. Then power from left green terminal = relay output (and terminal)
* To supply power on board control circuit, add 6-24V power to "ALT VIN" pins
[[category: ESP Relay Board]]