J12864

From ElectroDragon Wiki
Revision as of 12:42, 22 June 2018 by Chao (talk | contribs) (→‎Dimensions)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Reference

Arduino Code

Arduino code here

Notes:

  • The back of the module comes with 3 * 3 10K hard closure adjustable potentiometer VR1 could be transferred to the desired contrast (the default the 5V factory has good debugging own again adjust the potentiometer for fine tuning, please try to be careful debugging)
  • LED backlight polarity adjustable, JP4 LCD backlight plus or minus reverse at
  • The module comes with original Samsung genuine anti-static capacitance, anti-interference stronger C6 C7 C8
  • serial and parallel two ways to adjust the the PSB interface control two kinds JP2 shorted to P short circuit for the parallel port to the S serial
  • Self 3.3V through JP3 adjust the default access + level is 5V, then - is 3.3V, then C4 C5 polar capacitor can model 106A or 104A backlight resistor 33 ohm changed to 3.3 in Europe

Feature

J12864 Chinese character dot matrix LCD display module can display characters and graphics, built-in 8192 Chinese characters (16X16 dot matrix), 128 characters (8X16 lattice) and 64X256 dot matrix display RAM (GDRAM). The main technical parameters and display characteristics:

  • Power Supply: VDD 3.3V ~ +5 V (built-in booster circuit, without negative pressure);
  • Display: 128 × 64 lines
  • Display colors: yellow, and green / blue screen
  • Display angle look directly at: 6:00 minutes
  • LCD type: STN
  • MCU interface: 8-bit or 4-bit parallel / 3 serial
  • Configure LED backlight
  • A variety of software features: cursor display screen shift, custom characters, sleep mode, etc.

Dimensions

  • Dimensions: 93 × 70 × 12.5mm sight size: 73 × 39mm

J12864.png

Pins

Pins Name Direction Descripition
1 GND - Power GND
2 VCC - Power VCC
3 V0 - LCD Driver Power VCC
4 R/S(CS) H/L Data selection signal when parallel or chip selection when serial
5 R/W(SID) H/L read or right selection when parallel or data when serial
6 E(CLK) H/L enable when parallel or sync clock when serial
7 DB0 H/L data 0
8 DB1 H/L data 1
9 DB2 H/L data 2
10 DB3 H/L data 3
11 DB4 H/L data 4
12 DB5 H/L data 5
13 DB6 H/L data 6
14 DB7 H/L data 7
15 PSB H/L parallel or serial selection, H - parallel, L - serial
16 NC Null
17 RST H/L Reset, enable at low TTL
18 VOUT Voltage doubler output pin (VDD = +3.3 V effective)
19 LED-A (LED-5V) Backlight postive
20 LED-K (LED-0V) Backlight negative

Timing

Parallel

Write to module
J12864-parallel-1.png Read from module
J12864-parallel-2.png

Serial Timing

J12864-serial.png
Serial data transfer consists of three bytes to complete:
First byte: serial control - format 11111ABC

  • A control for the direction of data transfer: H data from the LCD to the MCU, L data from the MCU to the LCD
  • B is a data type selection: H indicates that the data is display data, L represents that the data is a control command
  • C is fixed at 0

8-bit data of the second byte: (parallel) 4 - format DDDD0000
Third byte: low 8-bit data (parallel) 4 - format 0000DDDD
Serial programming reference data
J12864-serial2.png

Command list

Command RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description Command Timing (540

KHZ)

Clear Display 0 0 0 0 0 0 0 0 0 0 Fill the DDRAM "20H", and set DDRAM address counter (AC) to "00H" 4.6ms
Reset address 0 0 0 0 0 1 S/C H/L X X Set DDRAM address counter (AC) to "00H", and move the cursor to the beginning of the position of the origin; This command does not change the contents of the DDRAM 4.6ms
enter into point setting mode 0 0 0 0 1 DL X 0RE X X Specified in the read and write data, set the cursor moving direction and specify display shift 72us
Display mode setting 0 0 0 1 AC5 AC4 AC3 AC2 AC1 AC0 D = 1: the overall display ON; C = 1: cursor ON; B = 1: cursor position ON 72us
Cursor or display moving control 0 0 1 AC6 AC5 AC4 AC3 AC2 AC1 AC0 Set cursor moving and display shift control bit; This command does not change the contents of the DDRAM 72us
Function setting 0 0 0 0 1 DL X 0 RE X X DL = 1 (must be set to 1); RE = 1: expansion of the instruction set of actions; RE = 0: The basic instruction set of the action 72us
set CGRAM address 0 0 0 1 AC5 AC4 AC3 AC2 AC1 AC0 Set CGRAM address to address counter (AC) 72us
Set DDRAM address 0 0 1 AC6 AC5 AC4 AC3 AC2 AC1 AC0 Set DDRAM address to address counter (AC) 0us
read busy(BF) sign and address 0 1 BF AC6 AC5 AC4 AC3 AC2 AC1 AC0 Read busy flag (BF) can confirm that the internal operation is completed, the value of the address counter (AC) can be read out 72us
write info into RAM 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Write data to the internal RAM (DDRAM / CGRAM / IRAM / GDRAM) 72us
Read data from RAM 1 1 D7 D6 D5 D4 D3 D2 D1 D0 Read data from the internal RAM (DDRAM / CGRAM / IRAM / GDRAM) 72us
Enter into standby mode 0 0 0 0 0 0 0 0 0 1 Fill the DDRAM "20H", and set DDRAM address counter (AC) to "00H" 72us
Roll address or IRAM address selection 0 0 0 0 0 0 0 0 0 SR Roll address, SR=0 allow input IRAM address
Display reverse selection 0 0 0 0 0 0 0 1 R1 R2 select any row in the four rows to display reverse, and decide if display reverse 72us
Sleep mode selection 0 0 0 0 0 0 1 SL X X SL=1, leave sleep mode, SL=0, enter into sleep mode 72us
extended function selection 0 0 0 0 1 1 X 1 RE G 0 RE=1, extended commands action, RE=0, basic commands action, G=1, drawing display on, g=0, drawing display off 72us
set IRAM address or Roll address 0 0 0 1 AC5 AC4 AC3 AC2 AC1 AC0 SR=1, AC5-0 is the vertical rolling address, SR=0, AC3-0 is ICON IRAM address 72us
Set drawing RAM address 0 0 1 AC6 AC5 AC4 AC3 AC2 AC1 AC0 Set CGRAM set address account (AC) 72us



Remarks:
1, when the module before the instruction, microprocessor Shun must make sure that inside the module in a non-busy state BF flag that reads BF needs to 0, before they can receive new instructions; send a command does not check BF flag, then the preceding instruction, and the middle of this command must be delayed for a longer period of time, that is, waiting for the previous instruction does execution completes, the instruction execution time, please refer to the individual instructions in the instruction table instructions.
"Re" is the basic instruction set and expansion instruction set selection control bit, when the "RE" bit is changed, the subsequent instruction set will be maintained in the final state, unless the "RE" is changed again bit, otherwise use the same instruction set, do not need to reset each time the "RE" bit.